ARS-2057P/2050PNative SATA Copy ControllerCopyright©2010 ACARD Technology Corp.Release: June 2010Attention:Wait over 5 seconds to power on after shutd
The diagram and photo below shows an ARS-2050P connected with a DVD-ROM, a SATA HDD and 10 DVD writers. 2.4.2 Installing the ARS-2050PAttention: When
3.1 Buttons and LCD DisplayThe ARS-2057P/2050P copy controller panel features 6 buttons and 1 LCD display. 3.2 About HDD InstallationAn HDD is not req
If the ARS-2057P/2050P does not have a 3.5" SATA HDD installed, its operating instructions are as follows: Insert a source BD/DVD in the BD/DV
Chapter 4 PCB LayoutThe layout of the ARS-2057P is shown below.J5: USB signal linkCN13: Connects to source BD/DVD-ROMCN12: Connects to SATA HDDCN2 &a
The layout of the ARS-2050P is shown below. J5: USB signal linkCN13: Connects to source BD/DVD-ROMCN12: Connects to SATA HDDCN2 & CN6(upper level)
Chapter 5 FunctionsThere are 12 major functions in the copy controller as the following figure shows, and there are subfunctions in Function 9, 10, 1
In Function 12 there are 22 subfunctions.* This is a special function. See P. 20 for details.15ARS-2057P/2050P Manual12. Advanced Setup12.1 UnderRun P
16During operation if you don’t understand an LCD message, see Appendix A . Now let’s take ARS-2057P to demonstrate.12. Adv Setup 5.1.1 UnderRu
17ARS-2057P/2050P ManualPress ENT to enter the following figure. The default is Off. Press ▼ to select On.Read Error Skip Off5.1.4 Format HDDNow pres
185.1.5 Verify HDDNow press ESC to return to Function 12, and then select part 5 Verify HDD as the following figure shows. Verify HDD is to verify if
Copyright and TrademarksThe information of the products in this manual is subject to change without prior notice and does not represent a commitment o
195.1.7 Update FirmwareNow press ESC and ▼ to enter the following figure. Update Firmware is to update firmware to the latest version. But you should
20Press ENT to enter the next figure. Use ▲ ▼ to confirm Yes or No.Load Default Config?Yes When default loading finishes, LCD will show the
215.1.14 CD-TEXTNow press ESC and ▼ to enter the following figure. CD-TEXT is a kind of special copying format. This function supports this special fo
225.1.16 Disc CounterNow press ESC and ▼ to enter the following figure. Disc Counter records how many discs you have copied.12-16. Adv Setup Disc Cou
2312-17. Adv Setup Auto Save ImagePress ENT to enter the next figure. The default is Off. Press ▼ to select On.5.1.17 Auto Save ImageNow press ESC and
Press ENT. The default is 5 second.AutoRun Time5 Press ▼ could select as off or 1~99 second.Press ENT to confirm the selecti
25Chapter 6 TroubleshootingChapter 6 Troubleshooting6.1 About LCDAfter you power up, if there is no display on the LCD, check if the connection of pow
Appendix A LCD Messages1. Normal Conditions:All data will be lost, erase?...All data on the disc will be lost. Confirm the erasing of da
No Image in Partition xx...There is no data image in partition xx.No Valid HDD!...
Technical Support FormEmail address: [email protected]: http://www.acard.comModel Name* (ex: ARS-2057P) Firmware version*System ConfigurationMo
Table of ContentsChapter 1 Introduction ... 1.1 Overview ...
5.1.12 ISRC & MCN ... 5.1.13 USB Option ...
WEEE StatementIn order to cope with the increasing waste electrical and electronic equipment, reduce the use of landfill and incinerator, and prev
WEEE бюлетеньЧтобЫ сρaвиться с увеличивающимся ненуҗным электрическим и электронным оборудованием, уменъшите использование закапывания мусора и испо
61.4 Systme Requirement Upright external cases ARS-2057P 9/10 × 5.25”ARS-2050P 12/13 × 5.25” SATA cable BD/DVD-ROM x 1 BD/DVD Writer x 7 (A
Chapter 2 InstallationBefore installing the ARS-2057P/2050P, please note that the product is provided in 3 types of packaging: Stand-alone Copy Contr
2.4 Installation Instructions8The diagram and photo below shows an ARS-2057P connected with a DVD-ROM, a SATA HDD and 7 DVD writers. 2.4.1 Installing
Commentaires sur ces manuels